How to Clean a Motorcycle Helmet – A Perfect Guide & Tips

If you have a passion for riding a good bike, chances are that you have an expensive motorcycle helmet. The helmet is an enclosed space that soaks up a ton of grime, metaphorically, from sweat to hair oil, it gets all of it. All the sweat, oil, breath, and in cases of emotional distress, tears, make the helmet smell awful with certain hygiene issues as well. So, you must know that How To Clean a Motorcycle Helmet.

It’s not just the inside that gets unbearable, but the outside of the helmet also catches all kinds of dirt and moisture as you race through fields and roads.

For this very reason, you need to keep your helmet clean and smelling fresh. Now the question is how to clean a motorcycle helmet which has cost you probably an arm, a leg and then some? Well, the answer is pretty simple, by following the simple few steps.

However, make sure to check for the instructions manual that might be there with your specific helmet. Certain helmets have specific instructions for managing and cleaning UV shields or anti-fog shields. So make sure that the cleaning process you choose does not contradict that of your helmet’s specific needs.

These steps can be time-consuming and may appear tiring, but better an exhausting day than a stinky trip!

Also, read about: Best Motorcycle Helmets

How to Clean a Motorcycle Helmet

Cleansing the Exterior of Helmet:

If we start from the outside, there are a number of things that you need to keep in mind before starting the cleaning process. The following are some:

Choosing the rags for the cleanup:

Know what material your helmet is made of. Different materials require different types of cleaning rags which can adapt to the texture and surface of the outside of the helmet better.

Generally speaking, getting a microfiber rag is the safest option for almost all types of surfaces. The rag’s texture makes sure that it does not scratch the helmet’s surface and causes any additional lines to appear.

The microfiber rag also helps in protecting the colors intact. However, make sure your rag is absolutely clean itself before using it to clean the helmet.

A toothbrush:

No, this toothbrush is not for your teeth, rather, it’s for your helmet’s hygiene. Use the toothbrush with soft bristles and fibers so that it does not scratch up the surface of your helmet. This one is for the hard to reach spaces inside your helmet.

Detergent:

Use a non-petroleum based detergent or better yet a shampoo that doesn’t have any such compounds. These help in making sure that the helmet is clean and the paints don’t get harmed in the process of scrubbing off the scum.

Also, use warm water to wash off the dirt and soap as you go.

Compressed air:

Compressed air is for cleaning those vents out as they can have stuff lodged in them as well. Keep in mind to not use canned compressed air as it can cause aerosol to stay inside the vent system which can later harm the helmet.

Side note: Remove all the electronics that you might have installed inside your helmet if you don’t want to buy new ones right after cleaning it.

Cleaning the outside:

After removing all the inner pads as well as the electronics (if you have any) make sure to clean the entire surface of the helmet with a rag dipped in warm water, warm, not hot.

Follow the steps below:

  1. Take the soaked, but not dripping, rag, and drape it over the entire helmet. This will help in speeding up the dislodgement of any dirt particles sticking tightly to your helmet. This will help to prevent the extra scratching of the shell or the face shield.
  2. Remove the rag after 5 to 10 minutes and take the face shield off. Most of the dirt would have soaked into the rag itself. Use a fresh rag for gently scraping away the rest of the dirt and grime away, while dunking the rag into warm water during the process.
  3. For the cracks and tricky spaces like vent outlets, use the soft-bristled toothbrush to scrape away the dirt.
  4. Next, blow into your vents using the compressed air. This will clean out the ducts if they have a large chunk of dirt or an insect stuck inside.
  5. Then it’s your face shield. Most modern face shields have an additional protective layer that is anti-fog or UV resistant. Cleaning your face shield with anything but warm water can accidentally damage these linings. Also, use your helmet’s manuals for proper instructions on cleaning your face shield.
  6. If your helmet has an inner sun visor, it must have been probably protected with from dirt as it is, however, there must be hints of dust over it which you might want to clean up. Again use warm water and microfiber rag to clean the surface of your sun visor.

Cleaning the interior of Helmet:

This process is fairly simple but the most important part of the cleaning process. The inside of the helmet is the smelliest part of the helmet as it has soaked up all the sweat, hair oil as well as breath into the cushion pads.

  • To clean these surfaces, take the cheek pads out and soak them in warm water, baby shampoo and leave it for some time.
  • Then take them out and scrub off all the grime, dip it again and then take it out to scrub. Repeat this process 2-3 times.
  • Be extra gentle while you scrub it off as using more strength can damage the interiors.
  • Let the pads dry, at least overnight so they can be fresh to use the next morning.

 

Conclusion
The above article has an answer to “How to Clean a Motorcycle Helmet?”. These simple steps can help you preserve your health while conserving the condition of the helmet itself. Following the steps given above, you can have a clean and fresh helmet for use on your next ride!

Read about: Best Safest Motorcycle Helmets

 

Leave a Comment